Resurrecting a Broken Motherboard – Bent Socket Pins
Linus Tech Tips
·Linus Tech Tips
·2018-05-06
·
1,765 words · ~8 min read
0:00
this is an ASUS zenith extreme
0:04
a 550 dollar
0:08
x399 motherboard for AMD's threadripper
0:11
CPU it was returned to me from one of the writers
0:15
and i was informed that it no longer
0:18
works uh okay well this is going to be and it's pretty anticlimactic here
0:24
i fixed it
0:33
hp's new omen x lineup comes equipped with Intel's seventh generation core i7
0:38
processors check them out at the link below
0:42
so what you observed just there was one of the many
0:46
peculiarities when it comes to bent pins
0:50
in a modern lga type CPU socket it can
0:53
manifest in any number of ways a failure
0:57
to post altogether an inability to detect memory inserted into certain
1:03
slots that one's actually very common or
1:07
the system can appear to be functioning completely normally all cores detected
1:13
all 128 gigs of RAM detected
1:17
the reason for this is that every CPU pin
1:21
has a slightly different function some of them are wired directly through
1:26
traces on the motherboard which you can actually see there's tons of traces
1:29
around a CPU socket to a contact point on a memory slot some of
1:34
them serve redundant purposes like to
1:37
act as a ground pin while others
1:42
may have no functionality whatsoever like they might be reserved for a future
1:47
CPU that might go into that socket with some
1:51
feature that might not ever get implemented so that
1:55
is why the symptoms of a bent CPU pin
1:58
can be as obvious as the system
2:01
not lighting up at all or as subtle as
2:05
slightly less stability when you're heavily overclocked
2:09
so one way or another
2:13
we need to fix this pin so no big deal Linus send it into the
2:18
manufacturer for repairs right wrong
2:22
first of all physical damage to the product is not
2:26
covered by any motherboard manufacturer that i'm aware of and they all consider
2:31
socket damage to be physical damage and number two
2:34
is an out of warranty repair to a CPU socket can cost as much as
2:40
350 dollars that's what i got quoted
2:44
when i wanted to repair a socket on an x99 ews motherboard even though it was a
2:49
400 board i'm not going to run out and spend 350 dollars so that i can have a b
2:54
stock board when it cost me 50 more dollars to just go buy a brand new one
2:58
so then with that in mind what do you
3:01
need to repair your own bent socket pins
3:05
really with a steady hand and a sewing needle you can probably do a pretty good
3:10
job but i've used everything from a pocket knife
3:14
to a sim removal tool to a thumb tack in
3:19
order to bend back pins and i've done it with all of those with success i even
3:24
used the pointy tweezers from an ifixit kit once
3:28
for today we're going to be using these picks that i actually just found here in
3:33
the workshop organization's beautiful right you're gonna save us so much time
3:36
in the future yeah it was super exciting and we're gonna be using these helping
3:41
hands with a magnifying glass something that i also recently bought just in case
3:46
someone bent a socket pin and they did so one of the trickiest parts of any
3:50
socket repair operation is figuring out where the bent pins are the best way to
3:55
do that is to get down low level with the socket
4:00
so that you can see whether it's straight across this way straight across
4:04
that way or at a diagonal you can see the gaps between the rows of pins that's
4:10
going to make it easier for your eye to pick out any imperfections for our case
4:14
we know exactly where it is so we're going to get up above it now we need to
4:18
assess the damage so we're just going to prod at it a little bit and this one
4:22
seems pretty obvious so you can see there's an even row of pins here and
4:27
even row pins here and then here there's a missing one now if this pin was broken
4:32
off we'd be in much rougher shape right now but you can actually see that it's
4:37
not it's just bent down so we just got to find
4:41
where it bent down to looks like uh
4:44
looks like it's down right there wow that is
4:47
that is dug in pretty deep there now there is always a risk
4:52
when you're working on something like this
4:55
that you will accidentally bend some other pins in the process
4:59
as long as you're careful it shouldn't happen
5:02
this pick might not actually be fine enough for me here i'm gonna go back to
5:06
my trusty knife i actually use the knife more often than
5:11
you'd probably think for this sort of thing so you want something that you can use
5:15
to get under the pin to pull it up there so you can
5:20
see i've pulled it up off the bottom now but
5:24
it's not quite aligned with the other pins so the chances of it
5:29
making perfect contact with the pads on the bottom of the CPU is pretty low now
5:33
that we've pried it up from the side the easiest way to attack it now is to go at
5:39
it from underneath head on that way you
5:42
can over bend it up a little bit so you want to come under it this way now
5:47
and over bend it up a bit because it's metal so
5:51
you can't just bend it to exactly where you want it
5:54
and then expect it to stay there okay cool that was exactly the desired result
6:00
there is we bent it up a little higher than we wanted and it settled right back
6:04
in exactly where it's supposed to be so now we can check the alignment of the
6:10
pins and we see a nice little bright dot
6:13
exactly where we expected perfectly aligned
6:16
let's go test it and we're back the system works
6:26
very good Linus you fixed a working motherboard ah
6:31
i have another trick for you up my sleeve this
6:35
is a sacrificial board from a project we never did because someone
6:41
a different member of our writing staff didn't realize that this motherboard
6:48
wasn't going to fit into any standard cases
6:52
so what we're going to do is we're going to simulate what would be a pretty common way to
6:58
damage a CPU socket oops that one was
7:01
actually accidental dropping the CPU as you go to install
7:07
oh okay yeah we definitely hit one let's try again
7:11
okay i'm having a pretty hard time uh mangling the socket here
7:16
now that that is a bent socket
7:21
let's try and fix it shall we something people might notice about this
7:25
second round of repair here is that i'm not even necessarily going
7:29
to try and get it exactly perfect because what you're going to realize
7:34
is that the contact pads on the bottom of the CPU are actually reasonably big i
7:39
mean they're not huge you still need to get pretty darn close
7:43
but if you are pretty close
7:46
and you remember too that when you put the CPU in it pushes down
7:51
into the lga the land grid array then as long as
7:56
you're good enough that once it gets pushed down a bit it'll be in pretty much the
8:01
right spot then you should be good enough
8:05
whoops this guy over here is probably still a
8:08
little bit too far out of alignment
8:14
now you want to make sure that you don't bend them down and up and down and up
8:19
too much because if you do that they lose their
8:22
strength and can eventually break off you can recover from that i have done it
8:27
by straightening out the shape of the pin
8:31
as long as there's enough left to get to the contact point
8:34
but it's not a sure thing and i did end up with a board that
8:38
i snapped off the top of the pad and uh
8:41
was not able to resurrect another key thing to watch out for when you're
8:45
looking for bent pins is that there are places where pins are missing
8:50
intentionally so it's always good to double check against a socket diagram
8:54
like see this corner right here there's no pin there that's fine
8:57
or another perfect socket that you have on hand
9:00
okay moment of truth time
9:03
okay there we go that beep is a good sign
9:08
and CPU detected two gigs of memory
9:13
yeah that's right repaired motherboard
9:19
so that's pretty much it guys how to bring your motherboard back from the
9:23
dead assuming that there aren't other issues on it like blown capacitors or
9:28
fizzled out resistors and
9:32
thanks for watching now let's say for a minute you make your
9:36
money doing like small-time computer repair like this for
9:40
others well then you want to check out freshbooks freshbooks is the cloud-based
9:44
accounting solution that lets you get paid faster be more organized and be
9:50
more productive spend your time doing
9:53
work so you can get paid like you can track your hours on a job you can build
9:58
a client through the platform you can even see when the client has seen the
10:02
invoice instead of spending your time fighting with a complicated accounting
10:07
solution at the end of the day when your brain's tired and you just plain don't
10:11
feel like it the best thing about freshbooks is you can try it out for 30
10:15
days for free by going to freshbooks.com
10:18
tech tips and entering Linus tech tips in the how you heard about us section
10:23
so thanks for watching guys if you dislike this video you can hit that button but if you liked it hit the like
10:27
button get subscribed maybe consider checking out where to buy that motherboards at the link in the video
10:31
description just in case this doesn't work for you
10:36
also down there we have a link to our merch store which has cool shirts like this one as well as our community forum
10:40
which you should totally join