Cooler Master HAF XB ATX Cube Gaming Case Unboxing & First Look Linus Tech Tips
Linus Tech Tips
·Linus Tech Tips
·2013-05-07
·
2,727 words · ~13 min read
0:07
welcome to my unboxing and first look at
0:10
what should be fairly evident based on the outside of the box this is the half
0:15
XB from Cooler Master which is a continuation of the ever popular half
0:20
Series so it started with the half 932
0:23
which was an ATX mid tower that offered
0:27
extreme airf flow for the price and for
0:31
the form factor I mean the whole thing was basically like mesh and fans and
0:35
making sure that all your system components stayed cool then we saw the
0:39
lower cost half 922 then I believe we saw the half X then the half
0:45
912 now we have a half Cube case now
0:50
Cube cases are more common with some of
0:54
these sort of bouquey case guys like we've seen a cube from uh Le and Lee
0:59
we've seen cubes from Mountain mods and case Labs over the years uh but most of
1:05
the mainstream guys don't really do cubes so I'm really excited to see what
1:11
sort of a a more experienced Casemaker
1:14
like Cooler Master can do with this form
1:18
factor the cube form factor is sort of unique because what it does do is it
1:22
gives a lot of room that you normally don't find in an enclosure above and
1:27
potentially below the motherboard because the motherboard
1:30
usually takes up a lot of space inside the case not because it is actually
1:35
physically large I mean a motherboard is thin but it takes up a lot of space
1:39
inside the chassis because you can't really put anything over top of it it's
1:44
it's just sort of it's sort of full so what you can do by lying the motherboard
1:48
down flat is you can get access to sort of unique ways to use the space so first
1:53
we see the packing material so you got a little about an inch and then a little
1:57
more than an inch on the sides and I mean honestly for a pretty this is
2:01
pretty light case considering its size and the steel construction it feels very
2:06
very sturdy like you could probably yeah just put all your weight on this thing I
2:09
mean like I said an experienced Casemaker like Cooler Master you don't
2:13
expect them to make any new bearers like it being kind of flimsy like you see
2:17
with mountain mods enclosures although those are all aluminum which is harder
2:22
to make more rugged and more strong so the first thing we're going to do is get
2:26
all these panels unscrewed actually not quite all of them cuz I want to show you the outside first so on the side you
2:32
find ventilation you expect that from a half series enclosure you also find
2:37
Handy Dandy handles that can be used for carrying the case around and you can use
2:41
to maneuver it quite easily these are not levers so you don't pull up on these
2:46
to open up the side panel the side panel is removed by removing the screws and
2:50
then sliding it back so those are just for air flow and for handling the case
2:55
the other side is identical same thing you got handles you got airflow holes so
3:00
nothing that you haven't seen before like 10 seconds ago all right on the
3:05
back we got a 120 mil fan more ventilation again as we've come to
3:09
expect 2 80 mil fans standard 7 PCI
3:12
slots as well as what appears to be a cable tie um and a protruded power
3:18
supply mounting cage so what that does is that gives us more room inside the
3:24
case for things like cable management cuz remember your power supply is going
3:27
to be like this long and then you're going to have a bunch of more space on
3:30
the end for where the cables need to come out so by doing this case
3:33
manufacturers instead of making their entire chassis another inch deeper can
3:38
just protrude the power supply a little bit and I guess sort sort of cheat give
3:42
you a smaller enclosure that way with just a little bit of a bump out the back
3:47
in the top you see what appears to be a 200 mm fan mounting uh fan mounting
3:53
spacing with rubber grommets and what is a very see-through mesh so while I like
3:58
to see Windows to see into my chassis and see what you know the cool Le stuff
4:03
that I put in there I don't mind a thin mesh like this because you can as you
4:07
can here as you can see you can see through it quite clearly so you'll get a
4:12
very good aesthetic even though it's not using a window on the front of the case
4:16
we've got two 120 mm fans with more mesh
4:19
two 5 and 1/4 in Bay two hot swap 3 and
4:23
1/2 in Drive sleds which are really cool because here check this out they're
4:27
compatible with 3 and 1/2 in or 2 and 1/2 in so this is that standard
4:31
rubberized uh grommet Mount thing that we've seen with Cooler Master in the
4:34
past you can put a 2 and 1 half inch Drive in using these holes more
4:37
ventilation on the drive cage itself and instead of bending it like we used to
4:42
you actually just slide it open and then clip it into place just like that with a
4:47
drive on it this allows it to be a lot more sturdy whereas on those other ones
4:51
like I know I've commented on this a lot in the past where I say yeah it looks
4:55
really flimsy once you put a drive in it it's okay now I no longer have to say
4:59
that it just doesn't look flimsy and once you put a drive in it it should be
5:03
that much that much more okay so those
5:07
lock into place quite nicely you've also got your front power reset uh indic uh
5:12
excuse me power LED you've got hold on
5:16
nope Power LED is the illuminated button here that's your hard drive activity LED
5:20
microphone headphone and two USB 3 ports
5:24
USB 3 is finally standard on pretty much
5:28
every single new case which is great I
5:31
remember it was so frustrating for so long uh you know half the chassis didn't
5:36
have USB 3 the other half of them had it but with a pass through that plugged
5:40
into the back of your motherboard so in order to put together your half XP
5:44
you're going to want to oh look at that wow considering the price of this case
5:48
that is a very very solid side panel I mean that's the thing again guys like
5:53
Cooler Master they do not screw around when it comes to the overall build
5:57
quality of the case so even though it's pretty light it's not like they're using
6:01
lightweight material I mean look at this they've punched out most of this panel
6:05
but it still has only this much Flex to it and I'm putting a lot of force on it
6:09
you can see from yeah no still good yeah you can see
6:14
how much force I'm putting on it it does not Bend at all extremely rigid love to
6:18
see that because it just means that there's going to be less strain on the
6:21
components if anything does happen if you're shipping the system which is a
6:25
concern if you're a system builder like NC you know you look at it and you go oh
6:29
well you know H that's going to put a lot of strain on the motherboard when
6:32
that when that case flexes like that not going to have that happen with a
6:36
well-built chassis so in terms of uh included accessories you've got tons of
6:41
cable management ties this is way more than I'm used to seeing with a case you
6:45
have a whole whack load of 2 and 1/2 in Drive sleds and I'll show you where
6:49
these go in a minute included speaker as well as all the screws you'll need to
6:53
assemble your system so once we get inside let's start on this side check
6:58
this out dedicated 2 and 1/2 in Drive mounting so with those two front hot
7:02
swaps you can mount up to six ssds in this case completely natively all you do
7:07
is throw your ssds in the little rails slide them in and it's pretty much what
7:11
you're used to seeing in terms of hard drive mounting except it's an entire
7:15
dedicated 2 and 1/2 in cage and again extremely wellb built at the back of the
7:19
case remember those 2 80 mil fans those are going to be directly cooling your
7:25
your ssds here and honestly I probably
7:28
wouldn't install anything here I just use them as passive airf flow the 5 and
7:32
1/4 in bays are completely toolless so you open them up lock them just like
7:36
that and you can remove them very easily and this is a design we've seen on the
7:40
half series before just by uh folding
7:43
back these little tabs which don't even look like a tab they're very well
7:46
integrated into the aesthetic design or the case which is very industrial and
7:51
then you use the toolless mounting in order to throw your 5 and a/4 in drive
7:54
in there lots of space at the back for longer Optical drives and cable
7:57
management speaking of cable management there are tons of cable management
8:01
options in this case check this out Cable Management Loops here I love these
8:05
things they're awesome they help you keep things tidy look at all the cable
8:08
management Loops that they've popped into the bottom here so you can see
8:11
those here all the cables that need to run even like they've even put in
8:15
dedicated Cable Management Loops for these fans at the back so you can go
8:18
cable here tie it down here tie it down there and get everything over to the
8:23
power supply area where you can see more cable management Loops more cable
8:27
management Loops the inter for the hot
8:30
swap 3 and A4 3 and 1/2 in Drive Bay in the front so single Molex power then you
8:35
run two SATA data cables in order to activate those you've got noise
8:38
dampening foam so this is under the power supply as well as a removable
8:44
filter that goes under the power supply itself they've also lifted the power
8:48
supply up a little bit and I'm glad to see that because I recently had a power
8:52
supply die in uh in an older defin R2
8:56
case from fractal this was totally my bad but what I did is I put a 120 mm fan
9:02
power supply in it fan down and then I put the case onto a carpeted area yeah
9:07
that thing died it totally starved from airf flow I didn't even think about it
9:11
as I was kind of throwing it under a desk and not thinking I was using it as a file server so this would have saved
9:16
my power supply right here cuz even though it wouldn't have been optimal it
9:19
would have been able to grab some air from the inside of the case by bringing
9:23
it up S through these gaps so it wouldn't have completely suffocated so
9:27
that yeah would have saved my bacon let's move up into the top of the
9:30
chassis where we find a couple cool things so number one is the removable
9:35
motherboard tray which you can take off just by removing four screws here and
9:39
lifting the whole motherboard tray out that'll make it easier to Cable manage
9:42
the bottom of the case as well as you know install all your components outside
9:46
of the case and then put them in personally I'd probably try and do it
9:51
without it because yeah my my hands are pretty small but I can handle it if you
9:55
have larger hands though that could be a boon for you huge CPU cutouts so you'll
9:59
have no problems installing the back plates of larger CPU coolers uh even
10:04
when the even when everything is still in the chassis even when the motherboard
10:07
is already installed on the motherboard tray you can see also that those front
10:11
120 mm fans also have 140 mm fan mounts
10:15
and the spacing looks right for a radiator which is outstanding because
10:20
you could put a dual 120 mm radiator here looks like you could pretty easily
10:25
fit ah yes you could easily fit another
10:28
120 mm radiator here that looks like enough spacing so you could have at
10:32
least a triple triple radiator water cooling setup in here with no problems
10:37
at all Aesthetics are awesome I mean if you're going to have that nice loose
10:41
mesh on the top so you can see everything inside the case then you
10:44
better make sure you're including things with black cables so black cabled fans
10:49
that are either either three pin or Molex another black cabled fan and all
10:54
black cables for the front panel connectors including the uh audio the uh
11:00
Power the and the LEDs the USB 3 as well
11:05
as yeah that's pretty much it hold on a sec guys here's something cool guys
11:10
check this out with a little bit of modding you could install a seven a
11:14
seven PCI slot motherboard but you could install a dual slot card in the very
11:19
bottom this is a big deal if you want to do sort of massive SLI configurations as
11:23
some boards don't have the correct spacing uh to put your last dual slot
11:28
card here because it just doesn't really work that way so check this out you can
11:32
put it here and then all you'd have to do is where you see you can put your
11:36
side panel on you can see the card's going to get lots of ventilation through these holes right over here so no
11:41
problems there so all you'd have to do is in order to use the uh rear exhaust
11:46
on your card potentially if you have a rear exhaust card is I'd probably you
11:49
know Dremel some holes kind of here so that you can uh you can get access to
11:53
that air flow so very cool stuff the Crazy Russian spotted that he's guest
11:57
helping me uh film today so kudos to him
12:00
for uh for noticing that that's awesome and I think that actually pretty much
12:04
covers it I just want to show you guys yet more cable management uh Loops right
12:08
here and here above the 5 and 1/4 in and the 3 and 1/2 inch cages I guess if I
12:13
had one thing to caution you guys about before buying this case is make sure
12:17
that you have an external storage solution because it only really supports
12:20
two 3 and 1/2 in drives other than that this guy is completely ready for SSD
12:26
more than anything else thank you for checking out my unboxing first look at
12:29
the half XP from Cooler Master don't forget to subscribe to Linus Tech tips
12:33
from boxing's reviews and other computer
12:36
videos here's something I didn't notice until we were putting the case back
12:40
together but check this out so those super sturdy plastic handles I showed
12:44
you on the outside are actually reinforced by this piece of metal here
12:48
that's part of why they're so strong and they're not going anywhere because
12:52
you're picking up the chassis by the actual chassis not by a piece of plastic
12:56
that's attached to the side panel which is attached to the chassis good stuff
13:00
again just great design choices overall on this case