welcome to the Fallout build log it was
said to not be possible to fit a computer into the bomb that comes with
the Fallout Anthology but with determination and a really good 3D
printer we're going to make it
work the master case 5 by Cooler Master gives you the freedom to truly make your
midtower PC case your own with a variety of modular parts and accessories check
out the link in the video description down below to learn more all right so
this isn't a normal build log as you can probably tell this isn't a normal case
uh with a normal case you can check what it's compatible with and just order
things that it's compatible with and put them in and everything's fine this is
obviously not naturally compatible with anything so there had to be some
feasibility testing I've already kind of planned out the parts I've got a Maximus
impact 8 I've got a tiny little sfx power supply from Silverstone this is a
300 WT trying to get a 450 more about that later I've got an R9 Fury Nano I
have some lowprofile Vengeance lpx I've
got an SSD uh Riser cable we'll talk
about that stuff later I've done some planning but one problem is part of that
planning involved being like well damn this thing is definitely too small if
you look at it the usable space is Tiny
it's not that big and a lot of its curves which are not that usable for
computer parts which are very much boxy so it needed to be extended I worked
with Taran and we 3D modeled some stuff so we did some test things first
surprisingly and awesomely Tan's first one actually fit quite well we did some
minor changes to the fit and added some fitting tabs for These Foo screws that
are on the side also worked quite well so we moved on to the jumbo the big guy
this one actually makes it tall enough that I can fit all of my stuff
now when looking at this it maybe doesn't look the greatest you might be
like but Luke it's lime green the rest
of it's not it's okay we'll get more to that
later I'm going to try to get some colorcoded spray bombs which actually
like match the green and the brown speckle that's already on here so we'll
we'll touch up the aesthetic there but for the rest of the build there's some
plans but not all of them is planned and you guys are going to have to come along
with me for that so with this build there has to be a
balance between badassery and functionality and one of the most
important things in my opinion with this build to do with badassery is this
button when you press this button right
now awesome super FY that's great but I
want this button to also turn on the computer I could have hooked it in and
parallel onto the power switchy thing using this and stuff but there's some
voltage problems or something I'm not super great with electronics so I'm
going to solder in another switch how this thing works is it's a big plate
that presses down onto another plate which has a button mounted in it so what
I'm going to try to do is add another button so that this plate press down
actually presses two buttons now I don't actually have another one of these spare
switches that's where
this hunk of junk comes in so this guy
up at the top I found has
very usable little tiny switch so I'm
going to drill the rivets out rip this
thing out separate it from these wires cut that
off tear it out mount it into that plate
solder it into the thing and then hopefully it
works I might just break it oh yes I
will just break it so it's actually just this module right here that I need
it's okay you're probably editing
this okay I think that opened it up for
me there we
go well I'm salvaging this computer case
I'm ripping out its switch and I'm using it for something else so if that's not
Fallout I don't know what it is I just need two of the wires and I only need
the ones that go to the actual switch itself one thing that's really cool that
I got for this build is this tiny little lowprofile SATA cable although the SATA
connections on this board are right next to the RAM so it's kind of a problem but
if I put it in the bottom slot down here
and just kind of work the cable around the bottom of the RAM but above the PCI
Express slot I can kind of make it come out just fine so this will work for my
SSD okay so I'm just testing to make sure that the system actually works so
this is the mess of components that I have to get inside of the
bomb we got post code nope there we go okay so I don't have a keyboard or
anything installed but as you guys can see on the monitor honestly that's good
enough the system works so moving on I need to turn this off then I need to
wrap um my switches things around these
poles maybe I can't wrap it around can I
get a Helper go hey
hey okay so now I need to solder this in
place so it's not just held by me thank you helper Colton you can go back to
doing whatever you're doing and we're good to go theoretically it works so now
as long as I don't massively screw up everything by my terrible soldering job
we're
good okay so my horrible horrible horrible horrible horrible soldering job
is done going to turn the power supply on doesn't automatically turn on that's
a good thing press the button yes okay the button works I need
to find a way to mount this little box on the plastic plate that is already in
there and already has one switch need to add another one God I'm happy that
worked this one has a lot more travel time than this one does this one's a
very shallow press also the button
swivels on a fix point on the bottom I would like to mount this as high as
possible but there's stuff blocking a
tall mount in here the ideal location is where this random kind of plus symbol
post is so I'm going to have to try to remove that and then drill through it
and see if I can mount something right
there might not want to show that it's
like not a proper way to use a drill just so Taran knows I'm just going to
hold my switch in the hole that I cut
for it this represents if I like hot glued it
in or something
okay that did not
work so it it works if you press like super deep I need to make the hole
bigger there is not that much time between now and when Fallout 4 comes out
if anything goes wrong I'm screwed and I'm doing a lot of things in this Build
That Could completely screw the entire build
over I hope this switch
works all right guys we're back in the office now one of the problems with
painting this is that the surface is very different than the surface of the
bomb the surface of the bomb is super smooth this guy has flat walls because
it's a 3D printer and it was printing kind of with some flat walls so I need
to sand that down so it's a little bit more smooth this is going to take a little while so super speed time lapse
engage I'm just going to tie a shirt on my
face okay so it's largely sanded down
this is filler primer so hopefully that will help kind of fill in some of the
grooves that are still existing and we can get going one of the problems is is
that the clearances on these things
are actually pretty tight so I'm going to try to tape them off and then we'll
be good to start spraying I've never
spray primered anything
before let's hope I don't super suck that would be a huge waste of
time wa what do you think any
problems that's a lot smoother I can already tell so we're going to bring
this into dry again then we might do it one more time so through the combined efforts of
my triangle file and my large flat file
I was able to open up that circular hole that I had drilled and make a square
hole and the switch fit through I need to secure it got some hot glue that
should be fine but there's one problem that remains it has to be so far out
that I can't actually slide it in because it will interfere with the rim
of the bomb so I have to actually take it
out and then put the switch plate back
in all the way and then fit it in why
this is a problem is I have to hot glue it in a
position that I can't can't take it out
and that sucks that's super sketchy but anyways let's give it a
shot don't touch it oh yeah that's
drives pretty fast though thankfully okay so everything's put
together if it doesn't work I'm going to pull my freaking hair out let's try
it it made the noise the computer turned on we're good to go moving on to other
things
all right guys this is primer coat number three it's starting to come along
um we might do one or two
more another problem to be solved the
power supply of this rig will be going into the top of the bomb up here I need
you to be able to plug into it into the bottom of the bomb so I need to create
an extension so I needed a right angle connector with a favorable Inlet so what
I did was I grabbed a right angle cable and I cut it in half without the camera
being turned on and then the plan is to strip off the end of this splice out the
wires solder the wires into this guy Mount this guy into the bottom of the
case plug this into the power supply and voila so here we
go okay so connection one is done just
like my other jobs little sloppy but it'll
do wow that one was like probably my best one okay so I've electrical taped
up my little thingy that I soldered together here so hopefully that looks
better for one and hopefully it works that's what we're going to test
now and with a whole lot of
Hope and it works
I was a little worried about that
okay okay okay okay moving on all
right all right this is our fourth and final coat of primer then we have to do
a layer of
black so I spray painted a bug onto the primer
okay so it's all primed we're ready to start painting um as with basically
everything else in this project I have no idea what I'm doing um but we're
going to start with black so this guy is black I believe lonus does know what
he's doing when it comes to the paint stuff but and he was supposed to show me
but he had to leave important business of some sort or something or other
whatever uh um so yeah he's not here so
we're just going to wing
it that's probably way more black paint than I
need but as I have no idea we're going to go with
that now lus said to roll down on this
thing towards the paint after dipping it in the paint for 2 minutes um um but I'm
kind of assuming that he was exaggerating a little bit cuz he thought
I wouldn't actually do it I'm just going to go for like a
while okay you have to look at this so I
just shoved two Ryobi batteries inside
of the thing so that it wouldn't move when I press paint on it and they
fit perfectly
so I think the 2 minutes of squeezing the paint out of it was a huge
exaggeration oh my God why is this so
bad and what is that
pattern when you take all the paint out of the brush you need a lot of pressure
behind it apparently so that's why it didn't work right away
Logitech has been in the headphone game for a really long time and it shows with
the g633 emis Spectrum headset the g633
is equipped with logitech's 40 mm proog audio drivers 7.1 Dolby Surround Sound
with Logitech gaming software a cardioid boom mic which hides away very nicely
actually fully adjustable RGB lighting and custom tags they're available from a
variety of retailers now including Amazon will be a great holiday gift for
your PC Xbox or PS4 Gamers or just a
great pick up for yourself if you're looking for a new headset check them out in the link in the video description
down below okay so our first coat of black is
done honestly it looks pretty okay there's definitely definitely areas
where it needs more paint so we will definitely definitely have to do another
coat but for now we're going to let it dry so I'm going to take it inside so
there's a little bit of a warmer climate at this time of night in the unheated
Warehouse it's like borderline too cold
to even be painting so I need to take it into the office so that it can actually
kind of warm up so that it can
dry okay