WEBVTT

00:00:00.560 --> 00:00:06.240
so we pulled off all of the tape and plastic covering bits so there were a

00:00:04.400 --> 00:00:10.360
few different ones uh first of all there's one holding the front bezel on

00:00:08.240 --> 00:00:13.679
because you can actually well my assumption is that you can actually pop

00:00:12.160 --> 00:00:17.800
that off but we'll figure that out later there was one holding uh this this piece

00:00:16.000 --> 00:00:22.000
closed um I think that was pretty much it for tape so let's start at the front

00:00:20.279 --> 00:00:26.960
so at the front we see just like the 800d we've got all of our front panel

00:00:24.480 --> 00:00:32.320
connectors why are you down there we've got all of our front panel connectors as

00:00:28.679 --> 00:00:34.640
well as our start and and uh Power LED

00:00:32.320 --> 00:00:40.559
reset switch all of that good stuff is up here I'm not sure where that other

00:00:36.840 --> 00:00:44.719
front USB 2.0 is I wonder if they mean

00:00:40.559 --> 00:00:47.039
either 4 USB 2.0 or 2 USB 3 2 USB 2

00:00:44.719 --> 00:00:51.399
either way it's no uh no major loss I mean you only need so many front USB so

00:00:49.079 --> 00:00:56.120
the overall fit and finish of the front bezel looks very very similar to the

00:00:53.280 --> 00:01:01.680
800d very nice quality very nice quality piece here okay so let's move around to

00:00:59.640 --> 00:01:07.280
Let's to this side okay so we' got a window which has kind of a frame around

00:01:04.320 --> 00:01:12.600
it okay gives it a very clean look the side panel is toolless so all you got to

00:01:09.360 --> 00:01:14.479
do is hold down these little um latches

00:01:12.600 --> 00:01:20.320
here and you can open and close it that way let's move around to the back where

00:01:16.680 --> 00:01:23.840
we will find eight expansion slots a 120

00:01:20.320 --> 00:01:27.240
mm exhaust fan our I/O slot as well as a

00:01:23.840 --> 00:01:29.520
bottom mounted power supply and a bottom

00:01:27.240 --> 00:01:34.880
mounted fan filter just like the 800d exception shorter and narrower all right

00:01:33.280 --> 00:01:40.240
then on the other side we're going to actually we're going to take this one right off I'm going to show you guys the

00:01:38.200 --> 00:01:44.119
overall look of the side panels so the side panels are quite stiff not a whole

00:01:42.119 --> 00:01:48.840
lot of flex to them you can see this mechanism here looks quite robust so

00:01:47.439 --> 00:01:55.000
you're not going to worry too much about that braking over extended use all right

00:01:52.320 --> 00:02:00.600
inside is all black as we've come to expect from cor aair cases you can see

00:01:56.840 --> 00:02:02.799
it has a huge CPU

00:02:00.600 --> 00:02:06.360
out so you're going to be able to access the back of your motherboard however and

00:02:04.920 --> 00:02:09.800
from whatever angle it is that you need to do that from okay let's finish up

00:02:08.200 --> 00:02:13.800
with the cooling first so up here in the top you can see we've actually got a lot

00:02:12.040 --> 00:02:20.840
of different fan mounting options so it comes with a 200 mm fan but you can also

00:02:16.840 --> 00:02:22.599
Mount 2 140s using these holes or 210s

00:02:20.840 --> 00:02:30.080
using I don't know what holes but use you can do 220s or 240s or a single 200

00:02:27.160 --> 00:02:34.040
mm okay let's go ahead and take this side panel off show you guys the inside

00:02:31.920 --> 00:02:38.560
of the window so that's a fixed with screws and it's just a piece of some

00:02:36.519 --> 00:02:43.920
kind of acrylic or Plexi something like that

00:02:40.720 --> 00:02:45.720
okay internal oh no one last external

00:02:43.920 --> 00:02:50.200
feature that I did want to show you guys actually if uh fine we can look at this

00:02:48.360 --> 00:02:54.720
now so here in the front we've got our Corsair logo and we've also got our

00:02:51.920 --> 00:03:01.360
other 200 mm fan and in terms of mounting options it looks like a 200 mm

00:02:58.000 --> 00:03:02.800
fan is all that goes there and you do

00:03:01.360 --> 00:03:07.920
not have the option to mount something else like you do in the top okay one

00:03:05.360 --> 00:03:12.040
last external feature up here in the in the top you can see right here gives us

00:03:09.879 --> 00:03:16.560
a guide so if you want to install a 3 and 1/2 in hot swap drive you can do

00:03:14.319 --> 00:03:21.159
that and it'll just push it down and if you want to install a 2 and 1/2 in hot

00:03:18.200 --> 00:03:26.280
swap drive then it'll guide it into the correct position so then you can swap it

00:03:23.920 --> 00:03:30.720
like it's hot it's crazy Russian wanted me to say

00:03:29.439 --> 00:03:35.519
that he's filming this for me in cameraman's dead cameraman's actually on

00:03:33.040 --> 00:03:38.840
vacation right now I can't get it out oh oh here hold on we've also got our fan

00:03:37.360 --> 00:03:44.319
speed controller in here I didn't even see that little switch so we basically

00:03:41.080 --> 00:03:47.000
got low medium and high I'm going to

00:03:44.319 --> 00:03:50.159
pull that out okay there good excellent closed all right let's have a look at

00:03:48.760 --> 00:03:54.000
the inside internal features we got our

00:03:52.439 --> 00:03:59.400
motherboard tray which is apparently designed by Corsair much like the rest

00:03:55.720 --> 00:04:01.879
of the case the grommets used here are

00:03:59.400 --> 00:04:07.400
um I'd say they're a little stiffer than some of the some of the uh well the most

00:04:05.200 --> 00:04:11.200
flexible ones that I've seen but you can clearly see that if you put something in

00:04:09.360 --> 00:04:13.799
put some pressure on it and withdraw it you're still going to they're still

00:04:12.480 --> 00:04:18.799
going to come back to their original position so nice high quality grommets

00:04:16.199 --> 00:04:22.479
uh the power supply Mount is raised up a little bit off the bottom of the case

00:04:20.320 --> 00:04:26.600
honestly it's pretty much irrelevant because you've got this ventilation here

00:04:24.720 --> 00:04:29.840
as well as this filtered intake so you can mount your power supply no matter

00:04:28.199 --> 00:04:34.800
what power supply you're using no problem fan side down so it can draw

00:04:32.240 --> 00:04:38.000
nice fresh air filtered air through the bottom of the case what else do we got

00:04:36.520 --> 00:04:44.400
in here here you can see the inside of the 200 mm fan that's included okay then

00:04:41.479 --> 00:04:48.520
we've also got a 120 mm fan at the back which wasn't mentioned actually on the

00:04:46.240 --> 00:04:53.440
outside of the box but I mean I can't imagine Corsair releasing a case without

00:04:50.479 --> 00:04:58.479
a 120 mm fan given that their water cooling solutions all rely on 120 mm

00:04:56.840 --> 00:05:01.720
fans so that wouldn't make any sense at all then would it we've also got

00:05:00.000 --> 00:05:05.280
speaking of water cooling a couple of water cooling grommets so if you wanted

00:05:03.240 --> 00:05:08.840
to do an external mounted rad you could run the tubing through there as I

00:05:07.080 --> 00:05:12.440
mentioned before at the back eight internal PCI Express brackets so that

00:05:11.080 --> 00:05:16.520
gives you a couple options you could install a motherboard with eight PC or

00:05:14.919 --> 00:05:20.240
did I say PCI Express I guess I meant PCI but either is fine uh so you can

00:05:18.759 --> 00:05:25.319
either install a motherboard with eight PCI slots at the back or you can install

00:05:22.600 --> 00:05:28.199
a motherboard with seven and a PCIe 16x slot at the bottom and then you can

00:05:26.639 --> 00:05:34.560
install a graphics card that is dual slot in there and it will still have room to exhaust all right we've got tons

00:05:32.479 --> 00:05:39.720
and tons of cable management grommets including uh gaps at the top here and

00:05:37.440 --> 00:05:44.000
more importantly here to bring through the 8 Pin or four pin CPU power

00:05:42.160 --> 00:05:49.039
connector or connectors what do we got here in terms

00:05:46.319 --> 00:05:55.120
of internal connectors speaking of connectors all right we've got uh a

00:05:51.800 --> 00:05:56.600
ziplock bag which has a Corsair sticker

00:05:55.120 --> 00:06:01.160
in all likelihood although I don't see it some rubber grommets some screws some

00:05:59.319 --> 00:06:08.960
zip TI okay here is all of our wow that's a

00:06:05.720 --> 00:06:11.639
whack of internal cables okay so I'm

00:06:08.960 --> 00:06:18.280
just going to try and find out how to how to take this

00:06:14.919 --> 00:06:20.080
off come on oh I see it's probably a

00:06:18.280 --> 00:06:27.120
fixed from the back yes yes it is that took me way too

00:06:24.039 --> 00:06:27.120
long to figure out

00:06:28.080 --> 00:06:33.440
okay there we go so this this is like a

00:06:31.560 --> 00:06:38.360
lot of cables it's a good thing Corsair makes all of their cables black

00:06:35.440 --> 00:06:43.520
otherwise managing all of this plus power supply plus whatever the heck else

00:06:40.319 --> 00:06:45.479
data cables you need would be a mess

00:06:43.520 --> 00:06:50.080
okay so back here we've got our fire wire we've got our HD audio we've got

00:06:47.360 --> 00:06:55.400
our USB 2 we've got our USB 3 you can see the way the USB 3 works is via the

00:06:53.880 --> 00:06:58.840
running out the back of the case and plugging into the back of the io Shield

00:06:57.120 --> 00:07:02.800
although I would expect adapters to be available fairly shortly so that you can

00:07:00.840 --> 00:07:07.919
use those brand new fancy internal headers with your brand new fancy case

00:07:05.919 --> 00:07:12.199
all right so that's all of that and then we've got fan connector okay no we've

00:07:10.680 --> 00:07:16.599
got our front panel so that's our power switch LEDs reset switch all that good

00:07:14.479 --> 00:07:20.160
stuff and then we have fan connectors so here's the power for the fan controller

00:07:18.440 --> 00:07:25.120
that we uh saw with that switch up at the top and then you can plug up to four

00:07:22.599 --> 00:07:28.319
fans directly into it and control all four fans so the four fans they intend

00:07:26.800 --> 00:07:35.840
for you to use are the 200 mil at the front a 120 m at the back and then up to

00:07:31.639 --> 00:07:38.120
240s or 2220s at the top we have a

00:07:35.840 --> 00:07:42.360
tooless mechanism here for the drive cages so it's just a simple rocker one

00:07:40.599 --> 00:07:47.080
so all you have to do is push that in well pull it out put in your drive push

00:07:44.639 --> 00:07:51.479
it in okay fairly straightforward and here we have toolless hard drive trays

00:07:49.840 --> 00:07:55.560
so they've got 2 and 1/2 in mounting holes here and then 3 and 1/2 in drives

00:07:53.639 --> 00:07:58.879
are going to be mounted via the pegs here they look flimsy but as soon as you

00:07:57.360 --> 00:08:04.080
put a drive in them and snap them in I guarantee you they're not going anywhere

00:08:01.720 --> 00:08:08.479
now one of these cages is actually removable actually these cages are

00:08:06.400 --> 00:08:15.039
removable and I believe they can actually be rotated

00:08:10.800 --> 00:08:16.639
but don't quote me on that one yet we

00:08:15.039 --> 00:08:23.919
will find out maybe it's just one of them that can be rotated here we go

00:08:19.159 --> 00:08:23.919
thumb screws handy love the thumb

00:08:24.280 --> 00:08:31.440
screws okay so that did

00:08:27.759 --> 00:08:31.440
that and then

00:08:31.479 --> 00:08:34.680
oh okay give me a moment here

00:08:35.599 --> 00:08:43.039
guys okay I was mistaken it looks like what this feature is actually for is to

00:08:40.760 --> 00:08:47.160
remove the hard drive cages which clearly we've done and then you can I

00:08:45.399 --> 00:08:51.640
guess you can access this fan to clean it for whatever reason or whatever but

00:08:49.279 --> 00:08:55.440
what it's also for is installing very very very long graphics cards so corser

00:08:53.560 --> 00:08:59.040
has left enough room for graphics cards to become pretty much double the length

00:08:57.040 --> 00:09:05.120
of a motherboard and you will still be able to to install them in the

00:09:01.399 --> 00:09:06.360
650d without any difficulty whatsoever

00:09:05.120 --> 00:09:12.600
okay the last thing we're going to show you guys in our unboxing and preview or

00:09:10.320 --> 00:09:17.399
whatever you want to call it first look that's what I usually call it is how to

00:09:15.040 --> 00:09:23.200
remove the front bezel so all you got to do is pull up these

00:09:19.959 --> 00:09:24.760
TS and remove the front bezel so the

00:09:23.200 --> 00:09:28.880
front bezel from the inside you can see it has a metal metal sheath outside of

00:09:26.839 --> 00:09:33.800
it but the inside is actually plastic we've got fan filter here which um H is

00:09:32.440 --> 00:09:38.120
or is not removable it's got to be it's got to be

00:09:38.800 --> 00:09:45.839
removable yes it's removable so there you go there's your front fan filter and

00:09:43.240 --> 00:09:51.720
it is removable maybe that's what crazy Russian was trying to show me earlier

00:09:48.880 --> 00:09:57.399
okay and then from the front you can I don't know install drives see fans

00:09:55.160 --> 00:10:04.560
uninstall this fan potentially thank you for checking out my video on the Corsair

00:10:00.480 --> 00:10:07.240
and I'll pose this here yeah that looks

00:10:04.560 --> 00:10:13.279
good it's not going to stay now stay on the Corsair

00:10:10.760 --> 00:10:19.079
650d don't forget to subscribe to lus Tech tips for more unboxings reviews and

00:10:15.440 --> 00:10:19.079
other computer videos