hello youtube today we're going to be sharing with you
our asmr pc build guide sponsored by e-boss
the brand for demand and sennheiser's
previous collaborative effort to build high-end gaming audio solutions
we'll be using their b20 usb type-c mic
for our voice recordings today so sit back relax and enjoy the sound
of bc building and look
i brought some friends to help out hi guys hi
hello hey hello let's get started
we need our usual tools
multi-bit screwdriver side cutters magnetic parts tray
anti-aesthetic angle strap cable ties attach your anti-static strap
to your ankle or wrist and then ground yourself to plugged in but powered off
power supply be careful we don't want to shock any of
our components
we're going AMD and it all starts here with the ASUS prime b550 plus
it's a great fit for your budget today while leaving space to upgrade when you
feel like you're ready remove it from the box and place the motherboard on top
of the box after you've removed all the extra contents like your i o shield
SATA cable and m.2 screw the box is a
perfect static safe workspace for pre-testing your hardware now get your
board ready for the next step by lifting the latch on the CPU socket
always open your CPU box carefully
AMD's ryzen 5 3600 features six zen 2
cores at up to 4.2 gigahertz boost and
we'd hate for you to damage them for AMD cpus the lettering always matches right
side up with the logo of the socket alternately you can match the golden
triangle with your board to make sure it seats properly when you're ready
gently press it into place give it a wiggle to make sure it went all the way
in then close and lock the latch
this last part can be a little scary but as long as you follow our instructions i
promise it'll be okay
to match our ryzen processor and to stay ready for potential future upgrades
we're installing two ac sticks of 3600 megahertz cl16 memory
it was only an additional ten dollars over the 3200 megahertz option and now
RGB saved us a few dollars after all today is about sounding good
rather than looking good open slots a2 and b2 on your motherboard
remove the modules from their packaging line up the notch on the bottom of the
module then slot them in gently but firmly until you hear a distinctive
click oh that's nice
severance one terabyte rocket NVMe SSD is a great value especially on sale
and our two terabyte seagate hard drive is perfect for all the thick games we're
gonna install we'll do the SSD now and
the hard drive later find your m.2 standoff that we grabbed
from our motherboard box and place it in the 80 millimeter slot
then remove your drive from its packaging and gently slide the notch
connection into the m.2 slot
hold the end down and screw it in with this teeny tiny am not two screw
our board comes with handy mounts for our cooler to latch onto but we're going
to use the hyper 212 mounting hardware instead
start by removing the back plate and standoffs by removing these four screws
here here here and here then simply pull brackets from the back
plate next remove our hyper 212 from its
packaging and grab the required am4 hardware
place the squared standoffs into the AMD holes like so then place the wider clips
over top place the prepped back plate on the back
of your board then screw on the standoffs to keep it in place
now take the two am4 brackets and place them over the standoffs like so
and fasten them down with the nuts making sure to keep the phillips pattern
on top remove the fat and heat sink from the box
peel the plastic off the bottom and remove the fan from the heatsink for
easier installation squeeze a pea-sized drop of thermal
paste onto the middle of the CPU heat spreader align your cooler so the screws line up
with the brackets and screw them down until it's nice and snug
there that's not going anywhere mount your fan by letting the clips rest
along these sides here and connect your fan to the CPU header
at the top of the board
the phantex b series is a great budget option that still gives you everything
you need in a case tempered glass side panel rubber
grommets good air flow plenty of space to work in and great cable management
you can save a bit of money by going with the last year's model like we did
with our b400a digital open the top of the box flip it over and
onto the floor or table whatever is easiest then slide
the box off remove the extra protective packaging
and stand your case upright remove the
glass panel and side panel and place it back in the box for now so it's nice and
safe the other side panel should be okay just
about anywhere with the panels removed unstrap all the
cables in the back and pull them out of the way for now then lay your case on
its side our standoffs come pre-installed but if
you're using a different case make sure to check the manual and put them in not
too many though now before we forget
install the i o shield by pressing firmly and clicking it into place
this cannot be done later if you forget now unless you want to take your
motherboard out of the case again grab your board and align it with the
standoffs and the i o shield ensuring that no tabs are sticking into the ports
once it's in place screw it down with these mounting screws
great job we're really getting there
take your hard drive from earlier and place it in one of the 3.5 inch bays at
the bottom of the case like so
our 650 watt modular power supply comes
from evga the g6 80 plus gold
you can save some money by going semi or non-modular but you could end up with
some extra clutter open the box and take out your psu and
its cables separate the atx 24 pin eps CPU eight
pin PCIe eight bin and SATA power
connectors plug these into the back your power supply don't force them
these can only go into your unit one way so if there's too much resistance you
might have done it backwards you silly goose with your cables attached slide the
power supply in sideways and pull your cables out of the way
take your four power supply screws and screw it in here here here
and here bye
let's start with our larger cables first shall we feed the atx 24 pin cable through the
top rubber grommet and plug it in here remove any slack and stuff under the
power supplies road good
next let's grab our eight pin eps cable and wrote it through the top cutout near
the plug this could take a little while but with some patience you'll get it through
plug it in then work the cable along the top
and down the side tucking it out of the way
now route your PCIe eight pin cable
through the rubber garment and leave it hanging roughly where your GPU will be
graphics cards often get in the way so i'll put it in last and plug it in
after now it's time to connect your case fans
the best bet for an easy and clean look
is to buy a three to one four pin fan splitter
connect all three of the splitter and then connect the splitter to an
extension and finally the extension to the chassis
fan header on the bottom of the board this is a lot easier than water cooling
but for tips on how to do your own hardline tubing make sure to get subscribed so you don't
miss out on our beginner's guide while we're here
let's plug in our hd audio cable here and our usb 3.0 cable here
connect your front panel headers in the proper configuration like so
and we're nearly done remember our hard drive
it's time to connect the SATA power and SATA data cables to the back of it then
route the data cable up through the bottom of the rubber grommet and into
the one of the SATA parts make sure
you put it in the middle or top slots though as the bottom one gets disabled
when you're using the second m.2 slot
and you may want to populate it down the line once everything is connected use ties or
zip ties to strap down any stray cables
trying to bundle them up for a cleaner look
if you want to get lazy that's okay
wiring mullets aren't the worst thing in the world as long as the front looks
pretty we know these are hard to come by right
now but if you can manage to get one anywhere close to msrp and rdx3060 is a
fantastic choice for 1440p gaming with the ryzen 5 3600
open the box remove the card from its esd bag and gently place it
the two slot covers here and here as well as the adjustable cover on the side
make sure the locking tab on the slot is open then grab the card and gently push
it into the slot until you see the lock close
it should make a little click replace the pci express slot cover
screws to hold it in place reattach the adjustable piece then plug in that final
loose pci express power cable now all that's left is to replace our
panels connect our monitor mouse and keyboard and turn it on
ah i love the sound of a successful first
boot wasn't that easy
are you as satisfied as i am of this beautiful new machine
i hope you enjoy the clicks and words as it processes your ever desire
listen to that um as the hard drives and fans power on
exquisite if you like how my voice sounds now and
throughout the video check out the new b20 from ebos
we recorded every word on it using the cardioid pattern but as three others for
all sorts of recording scenarios and you can tune the eq to your liking with
their digital gaming suite software
and hey for physical knobs on the device means you can change some settings without
even looking that's handy if you're a streamer or creator looking
for an alternative to existing usb mics look for it in the description below
it features nordic design premium construction and the high quality audio
you've been listening to for the past 10 minutes if you enjoyed listening today but want
to go Intel over emt for your own rig check out our first person view build
guide for tips on dealing with lga sockets it's 40 minutes long though so
strap ins for a bit of a long ride